#Soundmate firmware install
#Soundmate firmware serial
#Soundmate firmware update
#Soundmate firmware driver

It is strange to see eth0 port configured when this device is missing RJ45 connector. Listing of services shows that this device is using all Open source tools, main tool that enables music streaming is shairport which emulates Apple Airplay service. Overlayfs:/overlay 1.0M 64.0K 976.0K 6% /īy looking at free drive space we see that there is 976K of free space for any additional tools or scripts. So this device had 64Mb of ram, and more than half of it is free.įilesystem Size Used Available Use% Mounted on Telnet to device, and use 'root' for username and 'ifconfig' for password. Actually I'm puzzled how come we have just started to see consumer products use OpenWrt.

#Soundmate firmware install

OpenWrt is a not your average embedded OS, it is fully featured Linux with hundreds of packages which you can install with ease. Stream with EOS marker is not supportedLZMA ERROR 1 - must RESET board to recoverīut I can do the whole procedure again with the firmware provided in the first message.In this article I'll do a bit of digging under the skin and do some reverse engineering of SoundMate M1 audio streaming device. Īnd I'm sorry the firmware was not compatible or not copied correctly because I now have a different error. But I will start the router anyway, what can I do. See Linux Documentation/init.txt for guidance. Kernel panic - not syncing: No init found. VFS: Mounted root (jffs2 filesystem) readonly on device 31:2. JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. Mtd: partition 'rootfs' set to be root filesystem No RedBoot partition table detected in spi0.0 Searching for RedBoot partition table in spi0.0 at offset 0x7ff000 Searching for RedBoot partition table in spi0.0 at offset 0x7fe000

#Soundmate firmware driver

The last readable output in the screen was:Ĭonsole enabled, bootconsole disabledĪtheros AR71xx SPI Controller driver version 0.2.4 However the bootmanager shell did not support this command so I continued with I did not tell before but the copying was performed using Ubuntu 12.04, and I copied the firmware 1.1 version provided above.Īfter copying the system asked to check the firmware with a crc32 command.

#Soundmate firmware serial

The commands 'loads' and 'loadb' do not work, so transfer using serial line is not possible as far as I understand.īut anyone with a suggestion is welcome, I will try more. Tftpboot- boot image via network using TFTP protocolīootargs=console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ar7240-nor0:128k(u-boot),1024k(kernel),6912(rootfs),64k(config),64k(ART)īut I haven't found how I can upload the new firmware through the serial line (as the device doesn't have a ethernet connection). Using help I could get the basic informationīootm - boot application image from memory Finally I only typed 'n' during boot and then I got the shell. I tried every option I could find on the internet for more than a day. Using putty or hyperterminal I was able to see the booting, but it took me a day to find the command to get in to the u-boot shell. I bought a PL2303 cable and connected the Airmusic with my computer.

#Soundmate firmware update

Starting httpd server from server 192.168.222.6īut no wifi connection so I cant update firmware. LZMA ERROR 1 - must RESET board to recoverįailed to execute bootcmd, starting httpd to update firmware. Try update from pen drive again but no luck. When I upgraded firmware MW11, power lost.